![]() ![]() ![]() However, Schlage will continue to provide customer support and honor warranties on SecureKey locks. That’s another reason to select one manufacturer and stick with them because Kwikset and Schlage keys are not interchangeable.Įditors Note: Schlage has dicontinued its SecureKey technology that enabled homeowners to re-key locks. Kwikset offers re-keying technology (see link in related content section) that should help keep all your locks on one key. Finish it off by installing the new strike plate on the door jamb. This item: Honeywell 8101406 Classic Entry Door Knob and Deadbolt Lock Set, Oil Rubbed Bronze, 2-Pack 50.43 (25.22/Count) Amazon Basics Rounded 3.5 Inch x 3.5 Inch Door Hinges, 18 Pack, Oil Rubbed Bronze 25.49 (1.42/Count) Honeywell Safes & Door Locks 8101402 Honeywell Locking Door Knob, Oil Rubbed Bronze, Oil-Rubbed Bronze 20. Unlike the deadbolt, Kwikset keeps these screws easily accessible. Now, slide the inside knob on and tighten down the two screws. Put the outside knob on, feeding the rod through the latch. When you put the latch into the door, make sure the face hits the strike plate and not the other way around. Unlike a deadbolt, this is usually accomplished by flipping a pin to the correct position. Start with setting the backset on the latch. The steps to install a new door knob aren’t very different from a deadbolt. The last step for installing a deadbolt is to put the new strike plate on the door jamb. Schlage keeps everything together as one piece and eliminates this step, but you’ll be able to see the screw heads. Kwikset often secures the thumb turn with a tiny set screw. If there’s a faceplate, that snaps on next. The inner assembly goes on with the silver-colored piece underneath, and it’s all held together with two long screws. The rod that extends through the latch is asymmetrical so it only fits one way (the correct way). Discard it if the hole diameter is 1-1/2″. That metal collar should only be used for 2-1/8″ holes. Once you have the deadbolt screwed in, slide the outer cylinder in place. For instance, on the deadbolt below, it’s a simple matter of rotating the face of the deadbolt to the other position. Changing a Deadboltĭeadbolts will have a “this end up” arrow (or even the word) stamped on the side that will let you know how it should be oriented, and many can be adjusted for either backset distance. The process to install a Schlage or other competitors product is very similar. The pictures below show a Kwikset deadbolt and door knob. Make sure the new hardware will work with the holes in your door, otherwise you’ll be making another trip to the home improvement center. if installing a deadbolt, what is the hole diameter? It’s usually 1-1/2″ or 2-1/8″.if it’s a two hole door, what is the distance between the center of the two holes?.The door knob and deadbolt have the same key. It is suitable for any modern entrance door that requires a key, and it is also suitable for left and right hand doors. what is the backset (distance from the edge of the door to the center of the hole)? The backset usually measures 2-3/8″ or 2-3/4″. Our entry door knob and deadbolt set with classic oil rubbed bronze finishes, superb painting technology and durable stainless steel material, smooth, beautiful and durable.No matter what, here are some questions you should be able to answer: I’ve found it helpful to purchase new locks of the same brand as the old one to better avoid problems with hole size/ spacing. ![]() After you remove those, the latch should slide free. The latch or deadbolt is commonly secured with two screws into the end of the door. I’ve seen an older Schlage deadbolt that required the key to be turned part way before you could access the screws, and sometimes there are hidden releases or covers that conceal the fasteners. After you back those out, the interior and exterior assemblies can be removed. Most manufacturers will have two screws that are accessible on the interior assembly. knobs, handlesets, combo packs (with deadbolts ), and electronic locks. ![]() Removing the old hardware is usually a simple process. Schlage Bowery Matte Black Keyed Entry Lock Door Knob with Greyson Trim Rated. I tackled this project last weekend, and I took a lot of pictures so you can know what to expect when you change out your hardware. Swapping in a new knob or deadbolt can be done in as little as 15 minutes if you know what you’re doing. Fortunately, replacing existing door hardware is an easy project because you don’t have to worry about mortising the door or door jamb (like you would for a first-time installation). This entry set would be ideal for the front entry of a home.One of the questions readers are repeatedly asking us is how to install a door knob and deadbolt. Combo Pack: Single cylinder keyed entry door hardware is locked and unlocked from the exterior using a key in the deadbolt and the handle, and can be locked and unlocked from the interior using the thumbturn. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |